What changes when you build near the coast in NSW?

Salt air finds every exposed fixing on a coastal building. The exposure is classified first, and the materials list follows it.

What changes when you build near the coast in NSW?

Two things change: the salt in the air and the planning maps. AS 4312 classifies how corrosive the air is at a site, which sets the protection on steel, fixings, brick ties, flashings and roofing. Coastal sites often take a higher wind classification too. The Resilience and Hazards SEPP maps coastal management areas, which add planning matters to weigh.

Salt carried on the wind is the main thing that changes when you build near the NSW coast. It settles on metal and masonry, holds moisture against them and speeds up corrosion, so the closer a site sits to breaking surf, the more care the exposed details need.

The coast also has its own planning maps. Both are checked at feasibility, because together they set the materials list and the matters the consent authority will weigh.

How the exposure is classified

AS 4312, the Australian Standard for atmospheric corrosivity zones, sorts locations into categories from C1, very low, to C5, very high, with CX for the most extreme conditions. The category depends on how far the site is from the sea, whether that water is open surf or a sheltered bay, and the local wind and terrain.

Two sites a short distance apart can land in different categories. The classification is made for the actual site, and each product is then chosen against it.

The steel frame

Our module frame is hot-dipped galvanised steel with a powder-coated finish, bolted at galvanised gusset plates. Once the module is clad, the frame sits inside the wall, behind the cladding, away from direct salt spray and rain. The thinking behind the frame is covered in why is the structural frame over-engineered.

That moves the corrosion risk to the parts of the building that face the weather. Wall ties, lintels, flashings, roof fixings, gutters and balustrades are all specified to the exposure category.

Brick and mortar

Where the walls are brick, salt attacks the masonry near the coast in the same way it does on saline ground. Water carries it into the brick, then evaporates and leaves crystals that break the surface from the inside, as described in building on saline and reactive soil in Western Sydney.

So the bricks and mortar are chosen for the exposure, and wall ties are made to AS/NZS 2699.1 in durability classes that step up as the exposure gets more severe. Cladding choices are covered in external cladding selection and durability.

Roofs, fixings and unwashed surfaces

Roof sheeting and its fixings come in grades made for marine air, and the manufacturer's guidance on distance from the surf decides which one is used. The fixings also have to suit the sheet, because when two different metals touch in salt air, one of them corrodes faster.

Surfaces that rain never reaches corrode fastest. Salt builds up under eaves, inside gutters and on the sheltered side of a balustrade where nothing washes it off, so those areas are rinsed down as part of regular upkeep. The cost of that upkeep over time is covered in what does a modular building cost to maintain over its life.

Wind

Open water gives the wind a clear run at the shore, so coastal sites often take a higher wind classification, under AS 4055 for housing or AS/NZS 1170.2 for larger buildings. The roof tie-down and the connection between each module and the base structure are designed for that classification.

The planning layer

Coastal management areas are mapped under the Coastal Management Act 2016 and the State Environmental Planning Policy (Resilience and Hazards) 2021. They are the coastal wetlands and littoral rainforests area, the coastal vulnerability area, the coastal environment area and the coastal use area, and a site inside one of them carries extra matters the consent authority has to consider, such as public access to the foreshore and coastal hazards.

The maps are on the NSW Planning Portal spatial viewer, and a council's coastal management program can add local detail. We check them before design starts, so the building is drawn for the controls that actually apply to the land.

What the factory changes

The exposure is set by the site, and building in a factory does not change it. The factory changes the work inside the module. The frame, the services and the linings are fitted and inspected there before they are closed up, while the details on the outside are specified to the exposure category from the first materials list.

MADEmodular / MADEbetter.

How we deliver. Discuss your project.

MADEmodular / MADEbetter.

Let's talk.

Special-use accommodation, made better.